Archive for the ‘ art ’ Category

Latest 3d print: Botmobile

I thought it would be a good experiment to try 3d printing something ‘more complex’ on my Replicator:  Enter the “Botmobile”

First off, some pics!

Here’s all the 3d parts printed out, plus the electronics kit… which is no longer available in the Makerbot Store:  I talked with Makerbot support, they’ve discontinued it :-(

And here’s the finished thing:

It was quite a process to get everything printed out, but overall, really enjoyable and I didn’t encounter any problems.  I printed everything out in black ABS, and then spray-painted the body and wheels cherry-red (same as the previous bowl I printed).  The assembly went off without a hitch, and other than having to slightly adjust the front steering servo, it started driving right away.  Overall, I wouldn’t call it a ‘high performance’ RC vehicle:  Already the gearbox is starting to strip (and I can’t figure out why, it seemed pretty tight when assembled), and the front wheels hit the battery-box when turning sharp (underneath, in the middle) if you don’t trim it right.   But it does drive around and steer, so mission accomplished there.

Everyone’s been asking how long it took to print.  I’ve had little luck successfully using the ‘accelerated’ setting on my Replicator, so it’s all been ‘standard print times’.  There were multiple files to print, here’s the time estimates for each:

  • Windshield: 1h 7 min
  • Rear Axel: 1h 34 min
  • Back half of body: 4h 51 min
  • Front half of body: 5h 22 min
  • Gearbox: 2h 21 min
  • Interior seats: 2h 57 min
  • Front steering assembly: 1h 44 min
  • Wheels (all four): 8h 41 min

So that adds up to 28 hours 37 minutes.  It didn’t seem that long though:  Most of the long prints I did overnight:  I hooked up the printer to my a light timer (the type you plug your lights into when you go on vacation so you can turn them on\off at a certain time), and would set it to auto-turn off the printer about half hour after the print should finished.  Worked perfectly every time, didn’t have any misprints.

As of the time I printed it, I’m one of four people who have ‘made it’ on Thingiverse.  So it’s a unique feeling to know that… not many people on the planet have a 3d-printed RC car.  Here’s a few more pics:

New 3d print: ‘Decorative Bowl’

I got it in my head to try a ‘simple bowl’ print, and generated the below model in Maya.  It started out as NURBS, I slapped a lattice on it to get it into the desired shape, then converted it to polys for export.   It’s about 4.5″ wide, 5.75″ deep, and 2.5″ high.

The final product I painted two-tone with spray-paint:  The outer shell is a rubberized spray, I wanted to see how much it would ‘fill in’ the printing ridges.  After four coats, it had just started too.

The inside was sprayed with a bright cherry red.  None of the surfaces were sanded, but I think I’ll try that finishing method on the next one I print.

The whole thing took a bit over seven hours to print on my Makerbot Replicator.

You can download the .stl for printing from Thingiverse.

New custom 3d print: Hexagonal candle holder

I’m stuck with hexagons for the time being, I might as well accept it.

Last night I took a couple hours modeling up a candle-holder in Maya using hexagonal polygonal mesh.  Was an enjoyable process creating Python scripts for the generation and attaching of the mesh to the NURBS cylinder I used for the overall volume.  The whole thing took just under four hours to print on my Makerbot Replicator.

It easily fits a votive candle, or any other candle less than 2 1/4″ in diameter.  See more info on it, and download the .stl file for printing over on Thingiverse.

Ikea candle has a home.

 

Second custom 3d print: Another hex cloud

I’m apparently into hexagons these days.  I did another hexagonal design in Maya, printed it out on my Replicator with black filament (to contrast the white print I did last post).  This one took twice as long (8 hours) as the previous print as well, I’m guessing it has roughly twice the volume.  Currently I have it setup in my art-space holding a LED lamp I made using my Ostrich Egg-Bot (describe in a previous post), see pic below.  You can download the .stl file over on Thingiverse and print one yourself!  A day after submitting, it was added as a “Featured Thing” on their homepage, quite an honor :)

It makes a fine necklace holder

Lamp holder

 

Holes are 2 1/4" apart

My first custom 3d print: Hex Cloud

The past weekend I finally found time to make my first custom print for my Makerbot Replicator.  In Maya, I modeled & booleaned a variety of hexagonal mesh to create a “hexagonal cloud-like wall-hanger”.  I wanted to it to be artsy, and functional too:

Took just over four hours to print with two shells, and 10% infill.  I have to admit that it was a surreal experience to see the final print:  Just four hours ago this design was digital only, but now, it exists in the physical.  There’s a first time for everything.

To print it yourself, you can download the stl file over on Thingiverse.

Here is its (current) permanent home